The Quantum Blood and Fluid Warming System (IV Fluid ONLY Configuration) from Li
The Quantum Blood and Fluid Warming System (IV Fluid ONLY Configuration) from LifeWarmer is a Game-Changing innovation that has succeeded in closing a critical capability gap previously left exposed by other commercial off-the-shelf fluid warmers currently fielded. Size, weight, performance, and ease of use are no longer collective barriers to the delivery of whole blood in far forward and near point of injury (POI) prehospital casualty management.The Quantum exceeds all healthcare and logistical requirements for the delivery of warmed blood or fluids across the defined spectrum of care. The system consists of unique thermal administration sets that incorporate sensing elements with an integrated heating system that does not disrupt the fluid path. With advanced intelligence throughout the system, the lightweight Controller modulates and moderates the energy flow to the integrated heating elements to ensure consistent normothermic fluid delivery to the casualty. The 44V battery is the smallest in category, able to rapidly adjust power distribution based on the temperature and flow rate of the input fluid. This creates a highly efficient system capable of previously unrealized performance optimizations. The Quantum system has an operational weight of just 22 total ounces yet can deliver two units of 39°F Whole Blood (WB) at 100mL/min with an output temperature of 100.4°F (38°+/- 2°C) with only a 24 second warm-up period. The Quantum Blood and Fluid Warming System provides the Tactical Health Care Professional with significant technological overmatch in the fight to eliminate preventable combat death.Quantum System Contents:1 x Controller1 x Battery1 x Battery Charger2 x TIS (Thermal Infusion Set)NOTE: TIS is Single Use Only, Supplied sterile via Ethylene Oxide and Not Intended for use with Blood and Blood Products
The Quantum Thermal Transfusion Set- Blood from LifeWarmer is the revolutionary
The Quantum Thermal Transfusion Set- Blood from LifeWarmer is the revolutionary IV tubing set that allows for safe, rapid warming of blood, blood products, or IV fluids without adding hardly any additional steps to the normal IV setup process. Modeled after standard blood infusion tubing, the familiar configuration allows for ease of use. The sophisticated intelligence and proprietary warming technology are integrated into the tubing system for simplicity and to reduce additional equipment and procedural steps. Roughly the same size and weight as standard blood tubing, there is almost no additional equipment burden.The Quantum IV administration tubing is double-extruded to yield a configuration that has both an inner tubing layer and an outer tubing layer. A conductive heating element is between the two layers but does not come in contact with the fluid path or disrupt the laminar flow. The outer tubing layer acts as an insulator while the inner tubing layer transfers the heat from the heating element to the fluid path. Thermistors located in the tubing continually measure temperature and provide that input to the Quantum Controller. The monitoring and independent application of energy (heat) along the fluid path allows the Quantum to respond to varying temperature inputs from the fluid source to near the point of patient entry to ensure fluid temperature is the right temperature at delivery.The Quantum Life Warmer, fully charged, is able to warm and maintain up to 2 units ( 900mL +/- 100mL) of cold (4C) blood products or IV solutions to a pre-set temperature of 100.4F (38+/- 2C) at a flow rate of 100 mL/min (depending on the ambient temperature). Or, approximately 1700 mL of 20C IV solution to a set point of 38C +/- 2C at a flow rate of 200 mL/min. Effective warming flow rates range from 2 to 200 mL/minute depending on input fluid temperature and ambient conditions.
The Quantum Blood and Fluid Warming System from LifeWarmer is a Game-Changing in
The Quantum Blood and Fluid Warming System from LifeWarmer is a Game-Changing innovation that has succeeded in closing a critical capability gap previously left exposed by other commercial off-the-shelf fluid warmers currently fielded. Size, weight, performance, and ease of use are no longer collective barriers to the delivery of whole blood in far forward and near point of injury (POI) prehospital casualty management.The Quantum exceeds all healthcare and logistical requirements for the delivery of warmed blood or fluids across the defined spectrum of care. The system consists of unique thermal administration sets that incorporate sensing elements with an integrated heating system that does not disrupt the fluid path. With advanced intelligence throughout the system, the lightweight Controller modulates and moderates the energy flow to the integrated heating elements to ensure consistent normothermic fluid delivery to the casualty. The 44V battery is the smallest in category, able to rapidly adjust power distribution based on the temperature and flow rate of the input fluid. This creates a highly efficient system capable of previously unrealized performance optimizations. The Quantum system has an operational weight of just 22 total ounces yet can deliver two units of 39°F Whole Blood (WB) at 100mL/min with an output temperature of 100.4°F (38°+/- 2°C) with only a 24 second warm-up period. The Quantum Blood and Fluid Warming System provides the Tactical Health Care Professional with significant technological overmatch in the fight to eliminate preventable combat death.Quantum System Contents:1 x Controller1 x Battery1 x Battery Charger2 x TTS-B (Thermal Transfusion Set - Blood)NOTE: TTS-B is Single Use Only, Supplied sterile via Ethylene Oxide
The Life Warmer Quantum Controller is the command center of the Quantum Blood an
The Life Warmer Quantum Controller is the command center of the Quantum Blood and Fluid Warming System. It contains the microprocessor and control algorithm that continually assesses temperature input from tubing thermistors and regulates the energy provided to the tubing heating elements in the proximal and/or distal segments to reach and maintain temperature between 100.4°F (38°+/- 2°C) at patient delivery. The Controller receives power when connected to the Battery and modulates the energy flow to the TIS/TTS-B. The Quantum Controller has two connections, one for the battery and one for the Thermal Tubing of choice. The connection to the battery is an omni-directional plug for ease of insertion and the connection is safe and secure. The connection to the TIS or TTS-B is bi-directional and simple to execute- it’s plug and play.The Controller has LED lights on the shoulder of the device to inform the user about the output temperature and flow of the fluid. It will visually alert the care provider to the status of the system.The Controller is reusable and comes fitted with a Jacket that permits the mating (connection) of the TIS or TTS-B Life Warmer tubing circuit connector to the connector slot on the Controller.
The Quantum Charger from LifeWarmer is an AC-powered reusable device that can fu
The Quantum Charger from LifeWarmer is an AC-powered reusable device that can fully charge the Quantum Battery rapidly and safely. The Charger has built-in algorithms to ensure proper, steady charging without overcharging or damaging the health and integrity of the battery. The Battery can go from nearly 0% to full within 90 minutes. The Life Warmer Charger has two colored LED lights to inform the provider of the status of charge and condition of the battery.The Quantum Battery Charger connects to the Battery via an omni-directional plug that allows for rapid energy transfer while prioritizing safety even in cases of hasty disconnection. The Quantum Battery will alert the user if there is any issue associated with the health of the battery. The Charger comes supplied with a 6-foot AC power cord.
The Quantum Battery from LifeWarmer is an extremely powerful and intelligent bat
The Quantum Battery from LifeWarmer is an extremely powerful and intelligent battery in a small, lightweight package- weighing only 16 oz. The Quantum Battery powers the whole warming system with state-of-the-art Lithium Polymer cells harnessing 44 Volts of electrical potential. The battery, fully charged, is able to warm and maintain up to 2 units ( 900mL +/- 100mL) of cold (4C) blood products or IV solutions to a pre-set temperature of 100.4°F (38+/- 2C) at a flow rate of 100 mL/min (depending on the ambient temperature). Or, approximately 1700 mL of 20C IV solution to a set point of 38C +/- 2C at a flow rate of 200 mL/min.The Quantum Battery is built for use in the most austere and tactical environments. It is IP67 rated for water resistance and is the only portable fluid warming battery that has a disable feature on the audible alarm for tactical considerations. The Quantum Life Warmer Battery is rechargeable with a service life of 500 charge/discharge cycles.It is important to keep the Quantum Battery charged and ready for use. Always re-charge after deployment, even if the battery was not fully discharged. The battery can be kept plugged into the Quantum Charger, as the intelligent Battery senses charge demand and will charge as needed but never overcharge. The Battery has a “Status” button to check the state of charge at any moment, with 3 colored LEDs to inform the user about the condition of the battery.
The BIEGLER BW 685 / BW 685 S is a warmer for infusions or transfusions and oper
The BIEGLER BW 685 / BW 685 S is a warmer for infusions or transfusions and operates on the basisof a continuous flow warmer, where the heat from the heat exchanger is transferred via the extensionsets (consumables) to the liquid flowing within it.
Disposable product for single use only. Sterile and pyrogen-free flowtube. For u
Disposable product for single use only. Sterile and pyrogen-free flowtube. For use with Biegler blood and infusion warmer.
DANA Easy Setter is an accessory for insulin pump use. it helps the length of li
DANA Easy Setter is an accessory for insulin pump use. it helps the length of linking screw adjusted properly.If the length adjustment of linking screw is fail, the insulin could not be delivered.
DANA Diabecare ⅡS is external programmable syringe infusion pump used for the su
DANA Diabecare ⅡS is external programmable syringe infusion pump used for the subcutaneous delivery of insulin for the treatment of diabetes mellitus.
Description: The battery is an accessory for insulin pump use. it is the main po
Description: The battery is an accessory for insulin pump use. it is the main power of DANA insulin pump.
The linking screw is an accessory for insulin pump use. The role is to change th
The linking screw is an accessory for insulin pump use. The role is to change the rotary motion of the motor in insulin pump to rectilinear motion of plunger in insulin syringe reservoir.
Syringe cap and battery cap are accessories for insulin pump use. They helps the
Syringe cap and battery cap are accessories for insulin pump use. They helps the insulin pump used properly.
The disposable single-use Lavage Procedure Kit consists of a Tubing Set, Cannula
The disposable single-use Lavage Procedure Kit consists of a Tubing Set, Cannulae, Temperature Probes and a Fluid Reservoir. The Lavage Procedure Kit is supplied sterile.
The Recirculator 8.0 is comprised of two components: a portable control consol
The Recirculator 8.0 is comprised of two components: a portable control console and a single use disposable. The Console consists of a heater, pump, user touch screen, microprocessor, and interface electronics.The primary user interface is a color touch screen display that allows the user to make selections from the operating screen consisting of message display area, main screen area and flow control area. The touch screen also displays operating conditions, flow rate, output fluid temperature, patient temperature, target temperature, alarm and status messages, various timers and auxiliary temperatures. The Recirculator 8.0 monitors various sensors in the fluid path to ensure safe operation and alerts the user with alarms for out of specification conditions. Independent protection circuits prevent unsafe operation in the event of system software fault.The disposable single-use Lavage Procedure Kit consists of a Tubing Set, Cannulae, Temperature Probes and a Fluid Reservoir. The Lavage Procedure Kit is supplied sterile.
an Extension cable for connecting the system Base Unit (of Warrior/Warrior EXTRE
an Extension cable for connecting the system Base Unit (of Warrior/Warrior EXTREME) and the system Disposable Unit/Compact Disposable Unit
an Extension cable for connecting the system Base Unit (of Warrior/Warrior EXTRE
an Extension cable for connecting the system Base Unit (of Warrior/Warrior EXTREME) and the system Disposable Unit/Compact Disposable Unit
QinFlow Warrior Extreme system kit - the QiF warmer is a portable, inline blood
QinFlow Warrior Extreme system kit - the QiF warmer is a portable, inline blood and fluid warmer system. The QiF Blood and Fluid Warmer is located between the fluid container (intravenous fluid, blood or blood product) and treated patient, outside of the patient’s body.The kit contains 1 battery. The S/N of the kit is identical to the S/N of the Base Unit inside the kit.
QinFlow Warrior Extreme system kit - the QiF warmer is a portable, inline blood
QinFlow Warrior Extreme system kit - the QiF warmer is a portable, inline blood and fluid warmer system. The QiF Blood and Fluid Warmer is located between the fluid container (intravenous fluid, blood or blood product) and treated patient, outside of the patient’s body.The kit contains 1 battery. The S/N of the kit is identical to the S/N of the Base Unit inside the kit.
QinFlow Warrior Extreme Blood and Fluid Warmer Base Unit (BU). The BU controls t
QinFlow Warrior Extreme Blood and Fluid Warmer Base Unit (BU). The BU controls the performance of the system and the outflow fluid temperature. The BU contains firmware (SW) and electronics (HW), a graphic display and audio speaker for user notifications.
QinFlow Warrior Extreme Blood and Fluid Warmer Base Unit (BU)
QinFlow Warrior Extreme Blood and Fluid Warmer Base Unit (BU). The BU controls t
QinFlow Warrior Extreme Blood and Fluid Warmer Base Unit (BU). The BU controls the performance of the system and the outflow fluid temperature. The BU contains firmware (SW) and electronics (HW), a graphic display and audio speaker for user notifications.
QinFlow Warrior Extreme Blood and Fluid Warmer Base Unit (BU)
QinFlow Blood and Fluid Warmer QiF-01 Disposable Unit (DU) is a disposable cartr
QinFlow Blood and Fluid Warmer QiF-01 Disposable Unit (DU) is a disposable cartridge, provided sterile and ready for use. Inside the cartridge there is a tube which the fluid/blood flow through it and heated by it. While operation, the DU is connected to the Base Unit using a cable. The Disposable Unit has a standard intravenous tube extensions.
QinFlow Blood and Fluid Warmer QiF-01 Disposable Unit (DU)
QinFlow Blood and Fluid Warmer QiF-01 Disposable Unit (DU) is a disposable cartr
QinFlow Blood and Fluid Warmer QiF-01 Disposable Unit (DU) is a disposable cartridge, provided sterile and ready for use. Inside the cartridge there is a tube which the fluid/blood flow through it and heated by it. While operation, the DU is connected to the Base Unit using a cable. The Disposable Unit has a standard intravenous tube extensions.
QinFlow Blood and Fluid Warmer QiF-01 Disposable Unit (DU)
QinFlow Blood and Fluid Warmer QiF-01 Base Unit (BU). The BU controls the perfor
QinFlow Blood and Fluid Warmer QiF-01 Base Unit (BU). The BU controls the performance of the system and the outflow fluid temperature. The BU contains firmware (SW) and electronics (HW), a graphic display and audio speaker for user notifications.
QinFlow Blood and Fluid Warmer QiF-01 Base Unit (BU)
QinFlow Blood and Fluid Warmer QiF-01 Base Unit (BU). The BU controls the perfor
QinFlow Blood and Fluid Warmer QiF-01 Base Unit (BU). The BU controls the performance of the system and the outflow fluid temperature. The BU contains firmware (SW) and electronics (HW), a graphic display and audio speaker for user notifications.
QinFlow Blood and Fluid Warmer QiF-01 Base Unit (BU)